Month: July 2017

This is the first time for GN solids control to show our shaker screens at SPE Offshore Europe 2017 Exhibition.
The generation information of the exhibition is as below:

Show Name: SPE Offshore Europe Conference & Exhibition
Show date: Sep. 5th to 8th, 2017
Show address: Aberdeen, UK
Stand No.: 5A25
GN solids control will show our core products- shaker screens at the show. Even though the oil & gas drilling activities slowed down in the past years, shaker screen is the most consumpable wear parts of the shale shaker, the drilling companies need to use shaker screens every day, GN focus on the shaker screens technology improvement and marketing. We will send some screen samples to our potential drilling companies clients for testing before order.

We can produce OEM shaker screens for our own shale shaker GNZS703, GNZS594E, GNZS752, GNZS706 and the mud cleaner, also we can produce replacement shaker screens for other brand shale shaker, including FSI, KPT, Derrick FLC 500, FLC 48x 30, Brandt King Cobra, Venom, VSM 300, Swaco Mongoose, etc.
The possible failures of bad quality screens as below:
1) Rubbers not suitable for oil based drilling mud and not heat resistant for the high temperature drilling fluids
2) Wire mesh is easy damaged, working life is very short, need to be replaced frequently
3) Rubber sealing is not good , easily leakage of drilling mud
4) Screen dimension incorrect, can not install it on the shale shaker properly
5) Shaker screen frame working life is not very long, easy to break
6) Separation cut point did not comply with API RP 13C regulation, can not meet the drilling requirement by using the same API mesh
7) Effective screen area is not big enough, so it will influence the treating capacity
GN shaker screen has solved the problems above, welcome to visit GN stand to know our shaker screens.

This week GN solids control shipped one set of 1000HP rig solids control system to Romania.
The technical specs are as below:

5 sets of container sized mud tanks, with safety guard handrails, walkways, stairs, valves, flexible connection.
3 units of shale shaker
1 unit of mud cleaner
1 unit of vacuum degasser
2 units of desander desilter feeding pump
2 units of mixing pump
2 sets of mixing hopper
20 units of mud agitator

1 set of ATEX, CE certified electric control system to control all the motors in the solids control system, and explosion proof cables, gland, starters, motors
The mixing pump, charging pump, feeding pump all with the same model centrifugal pump, all the spare parts are replaceable with Mission Magnum pump.

All the compartment with proper size mud agitator except for sand trap.
Recently we have several mud tank systems under construction, the workers have to working hard by 2 shift everyday to finish the production, through the proper management and arrangement, we finished the order on time.
The shale shaker and mud cleaner bottom shaker has the same model shaker, we produce our own shaker screens for our shale shaker. Our composite material shaker screen dimension is replaceable with Swaco Mongoose PT shaker screen. The composite material screen has longer working life and larger effective screen area, better separation performance, the composite material frame is thinner than metal frame, so the effective screen area became larger.

Continue reading “1000HP rig solids control system shipped to Romania”

Several month ago, GN solids control shipped 2 sets of oil sludge separation system to Middle east client, now the oil sludge separation system has been installed successfully in the client’s site.

The complete oil sludge separation system including:
1)    Pre-mixing unit
The function of pre-mixing unit is increase the flowability and lower the viscosity of the oil sludge through the agitating and heating line, the boiler can provide the hot steam to the heating lines to heat the oil sludge. The oil sludge is storaged in the waste pit and it is transferred by vacuum pump to the pre-mixing tank. But the client needs a air compressor for the working of vacuum pump.

2)    Shaker tank unit
The shale shaker is special designed with cover to avoid the oily sludge splashing and there is hot water spray line to spray hot water to the shaker screen, to prevent the shaker screens from blocking, which will make the shale shaker working better.
3)    Decanter centrifuge separation unit

We provide different model decanter centrifuge with different treating capacity with oily sludge, right not we have 10m3/h decanter centrifuge and 20~25 m3/h decanter centrifuge. The VFD control panel is installed on the telescopic skid with the screw pump. The static mixer is used to mix the chemical before feeding to the centrifuge feed pipe.
4)    Chemical dosing unit
The chemical dosing unit is installed in the 20ft container for convenient operation and shipment.
5)    3 phase separation unit
The 3 phase separation unit including slant plate clarifier, gravity type oil water separator and micro bubble type oil water separator. The clear water and clear oil is flow to the water buffer tank and oil buffer tank. The water pump and oil pump will transfer the water and oil to the storage tank automatically once it is reach the setting value.

As a professional manufacturer of centrifugal pumps in China, GN solids control can produce replacement spare parts for Mission Magnum series centrifugal pump.

Welcome to contact with GN solids sales to get the explored view and part number for the spare parts inquiry.
The centrifugal pump with the spare parts are the most consumpable parts for the solids control system, it can be worked as trip pump, super charging pump, mud cleaner feeding pump, centrifuge feeding pump, vacuum degasser jetting pump, transfer pump, mixing pump, etc.With the features below, it has been widely used for oil & gas drilling solids control system, horizontal directional drilling mud recycling system, core bed methane drilling mud cleaning, geothermal drilling, water well drilling, sludge separation system, mining solids removal unit, etc industries.
1)    Cost effective, steadily working compared with screw pump, low cost to get the wear parts
2)    Easy maintenance, easy operation, easy to source the spare parts, standard design
3)    Flexible to install on the mud tank, have no strict requirement for the installation conditions, for example, it can be installed under the sand trap, on the tank skid, besides the hopper or directly on the ground with skid and control panel on it.
It also has disadvantages for some special applications as below:
4)    Horizontal installed, it takes much more area on the mud tank compared with vertical installed pump, like submersible slurry pump
Continue reading “Mission pump spare parts for sale”